Daily Papers

Generalizable humanoid loco-manipulation poses significant challenges, requiring coordinated whole-body control and precise, contact-rich object manipulation. To address this, this paper introduces HOMIE, a semi-autonomous teleoperation system that combines a reinforcement learning policy for body control mapped to a pedal, an isomorphic exoskeleton arm for arm control, and motion-sensing gloves for hand control, forming a unified cockpit to freely operate humanoids and establish a data flywheel. The policy incorporates novel designs, including an upper-body pose curriculum, a height-tracking reward, and symmetry utilization. These features enable the system to perform walking and squatting to specific heights while seamlessly adapting to arbitrary upper-body poses. The exoskeleton, by eliminating the reliance on inverse dynamics, delivers faster and more precise arm control. The gloves utilize Hall sensors instead of servos, allowing even compact devices to achieve 15 or more degrees of freedom and freely adapt to any model of dexterous hands. Compared to previous teleoperation systems, HOMIE stands out for its exceptional efficiency, completing tasks in half the time; its expanded working range, allowing users to freely reach high and low areas as well as interact with any objects; and its affordability, with a price of just $500. The system is fully open-source, demos and code can be found in our https://homietele.github.io/.

Reasoning from sequences of raw sensory data is a ubiquitous problem across fields ranging from medical devices to robotics. These problems often involve using long sequences of raw sensor data (e.g. magnetometers, piezoresistors) to predict sequences of desirable physical quantities (e.g. force, inertial measurements). While classical approaches are powerful for locally-linear prediction problems, they often fall short when using real-world sensors. These sensors are typically non-linear, are affected by extraneous variables (e.g. vibration), and exhibit data-dependent drift. For many problems, the prediction task is exacerbated by small labeled datasets since obtaining ground-truth labels requires expensive equipment. In this work, we present Hierarchical State-Space Models (HiSS), a conceptually simple, new technique for continuous sequential prediction. HiSS stacks structured state-space models on top of each other to create a temporal hierarchy. Across six real-world sensor datasets, from tactile-based state prediction to accelerometer-based inertial measurement, HiSS outperforms state-of-the-art sequence models such as causal Transformers, LSTMs, S4, and Mamba by at least 23% on MSE. Our experiments further indicate that HiSS demonstrates efficient scaling to smaller datasets and is compatible with existing data-filtering techniques. Code, datasets and videos can be found on https://hiss-csp.github.io.

This paper describes the design and implementation of a ground-related odometry sensor suitable for micro aerial vehicles. The sensor is based on a ground-facing camera and a single-board Linux-based embedded computer with a multimedia System on a Chip (SoC). The SoC features a hardware video encoder which is used to estimate the optical flow online. The optical flow is then used in combination with a distance sensor to estimate the vehicle's velocity. The proposed sensor is compared to a similar existing solution and evaluated in both indoor and outdoor environments.

If human experience is any guide, operating effectively in unstructured environments -- like homes and offices -- requires robots to sense the forces during physical interaction. Yet, the lack of a versatile, accessible, and easily customizable tactile sensor has led to fragmented, sensor-specific solutions in robotic manipulation -- and in many cases, to force-unaware, sensorless approaches. With eFlesh, we bridge this gap by introducing a magnetic tactile sensor that is low-cost, easy to fabricate, and highly customizable. Building an eFlesh sensor requires only four components: a hobbyist 3D printer, off-the-shelf magnets (<$5), a CAD model of the desired shape, and a magnetometer circuit board. The sensor is constructed from tiled, parameterized microstructures, which allow for tuning the sensor's geometry and its mechanical response. We provide an open-source design tool that converts convex OBJ/STL files into 3D-printable STLs for fabrication. This modular design framework enables users to create application-specific sensors, and to adjust sensitivity depending on the task. Our sensor characterization experiments demonstrate the capabilities of eFlesh: contact localization RMSE of 0.5 mm, and force prediction RMSE of 0.27 N for normal force and 0.12 N for shear force. We also present a learned slip detection model that generalizes to unseen objects with 95% accuracy, and visuotactile control policies that improve manipulation performance by 40% over vision-only baselines -- achieving 91% average success rate for four precise tasks that require sub-mm accuracy for successful completion. All design files, code and the CAD-to-eFlesh STL conversion tool are open-sourced and available on https://e-flesh.com.

Hall effect thrusters are one of the most versatile and popular electric propulsion systems for space use. Industry trends towards interplanetary missions arise advances in design development of such propulsion systems. It is understood that correct sizing of discharge channel in Hall effect thruster impact performance greatly. Since the complete physics model of such propulsion system is not yet optimized for fast computations and design iterations, most thrusters are being designed using so-called scaling laws. But this work focuses on rather novel approach, which is outlined less frequently than ordinary scaling design approach in literature. Using deep machine learning it is possible to create predictive performance model, which can be used to effortlessly get design of required hall thruster with required characteristics using way less computational power than design from scratch and way more flexible than usual scaling approach.

BLDC motor applications require precise position and speed measurements, traditionally obtained with sensors. This article presents a method for estimating those measurements without position sensors using terminal phase voltages with attenuated spurious, acquired with a FPGA that also operates a PWM-controlled inverter. Voltages are labelled with electrical and virtual rotor states using an encoder that provides training and testing data for two three-layer ANNs with perceptron-based cascade topology. The first ANN estimates the position from features of voltages with incremental timestamps, and the second ANN estimates the speed from features of position differentials considering timestamps in an acquisition window. Sensor-based training and sensorless testing at 125 to 1,500 rpm with a loaded 8-pole-pair motor obtained absolute errors of 0.8 electrical degrees and 22 rpm. Results conclude that the overall position estimation significantly improved conventional and advanced methods, and the speed estimation slightly improved conventional methods, but was worse than in advanced ones.

In this work, we present a new approach for fast tracking on multiwire proportional chambers with neural networks. The tracking networks are developed and adapted for the first-level trigger at hadron collider experiments. We use Monte Carlo samples generated by Geant4 with a custom muon chamber, which resembles part of the thin gap chambers from the ATLAS experiment, for training and performance evaluations. The chamber has a total of seven gas gaps, where the first and last gas gaps are displaced by ~1.5 m. Each gas gap has 50 channels with a size of 18-20 mm. Two neural network models are developed and presented: a convolutional neural network and a neural network optimized for the detector configuration of this study. In the latter network, a convolution layer is provided for each of three groups formed from 2-3 gas gaps of the chamber, and the outputs are fed into multilayer perceptrons in sequence. Both networks are transformed into hardware description language and implemented in Virtex UltraScale+ FPGA. The angular resolution is 2 mrad, which is comparable to the maximum resolution of the detector estimated by the minimum chi2 method. The latency achieved by the implemented firmware is less than 100 ns, and the throughput rate is 160 MHz.

Hall-effect thrusters (HETs) are widely used for modern near-earth spacecraft propulsion and are vital for future deep-space missions. Methods of modeling HETs are developing rapidly. However, such methods are not yet precise enough and cannot reliably predict the parameters of a newly designed thruster, mostly due to the enormous computational cost of a HET plasma simulation. Another approach is to use scaling techniques based on available experimental data. This paper proposes an approach for scaling HETs using neural networks and other modern machine learning methods. The new scaling model was built with information from an extensive database of HET parameters collected from published papers. Predictions of the new scaling model are valid for the operating parameters domain covered by the database. During the design, this model can help HET developers estimate the performance of a newly-designed thruster. At the stage of experimental research, the model can be used to compare the achieved characteristics of the studied thruster with the level obtained by other developers. A comparison with the state-of-the-art HET scaling model is also presented.

WiFi Channel State Information (CSI)-based human activity recognition (HAR) enables contactless, long-range sensing in spatially constrained environments while preserving visual privacy. However, despite the presence of numerous WiFi-enabled devices around us, few expose CSI to users, resulting in a lack of sensing hardware options. Variants of the Espressif ESP32 have emerged as potential low-cost and easy-to-deploy solutions for WiFi CSI-based HAR. In this work, four ESP32-S3-based 2.4GHz directional antenna systems are evaluated for their ability to facilitate long-range through-wall HAR. Two promising systems are proposed, one of which combines the ESP32-S3 with a directional biquad antenna. This combination represents, to the best of our knowledge, the first demonstration of such a system in WiFi-based HAR. The second system relies on the built-in printed inverted-F antenna (PIFA) of the ESP32-S3 and achieves directionality through a plane reflector. In a comprehensive evaluation of line-of-sight (LOS) and non-line-of-sight (NLOS) HAR performance, both systems are deployed in an office environment spanning a distance of 18 meters across five rooms. In this experimental setup, the Wallhack1.8k dataset, comprising 1806 CSI amplitude spectrograms of human activities, is collected and made publicly available. Based on Wallhack1.8k, we train activity recognition models using the EfficientNetV2 architecture to assess system performance in LOS and NLOS scenarios. For the core NLOS activity recognition problem, the biquad antenna and PIFA-based systems achieve accuracies of 92.0pm3.5 and 86.8pm4.7, respectively, demonstrating the feasibility of long-range through-wall HAR with the proposed systems.

The ongoing expansion of urban areas facilitated by advancements in science and technology has resulted in a considerable increase in the number of privately owned vehicles worldwide, including in South Korea. However, this gradual increment in the number of vehicles has inevitably led to parking-related issues, including the abuse of disabled parking spaces (hereafter referred to as accessible parking spaces) designated for individuals with disabilities. Traditional license plate recognition (LPR) systems have proven inefficient in addressing such a problem in real-time due to the high frame rate of surveillance cameras, the presence of natural and artificial noise, and variations in lighting and weather conditions that impede detection and recognition by these systems. With the growing concept of parking 4.0, many sensors, IoT and deep learning-based approaches have been applied to automatic LPR and parking management systems. Nonetheless, the studies show a need for a robust and efficient model for managing accessible parking spaces in South Korea. To address this, we have proposed a novel system called, Shine, which uses the deep learning-based object detection algorithm for detecting the vehicle, license plate, and disability badges (referred to as cards, badges, or access badges hereafter) and verifies the rights of the driver to use accessible parking spaces by coordinating with the central server. Our model, which achieves a mean average precision of 92.16%, is expected to address the issue of accessible parking space abuse and contributes significantly towards efficient and effective parking management in urban environments.

With growing, Car parking increases with the number of car users. With the increased use of smartphones and their applications, users prefer mobile phone-based solutions. This paper proposes the Smart Parking Management System (SPMS) that depends on Arduino parts, Android applications, and based on IoT. This gave the client the ability to check available parking spaces and reserve a parking spot. IR sensors are utilized to know if a car park space is allowed. Its area data are transmitted using the WI-FI module to the server and are recovered by the mobile application which offers many options attractively and with no cost to users and lets the user check reservation details. With IoT technology, the smart parking system can be connected wirelessly to easily track available locations.